Send E-mail
1. High quality elastic steel material with long use time.
2. Type: Draw Bar and Tang
3. Shank of the Shell End Mill Arbors: MS1-MS5 BT30 BT40 BT50 DIN69871 A30 DIN69871 A40 DIN69871 A50 CT30 CT40 CT50
4. Suitable Facing Cutter：13mm-60mm
5. The precision little than 0.005mm with balance 8000rpm. Higher precision also can be made by your demand.
6. Holder hardness:48-55HRC
7. Suitable Pull Stub& Facing Cutter is also upon request.
| HT-0040 | MORSE TAPER SHELL END MILL ARBORS (TANG TYPE) | ||||||
| Order No. | D | d | W | Order No. | D | d | W |
| (mm) | (mm) | (mm) | (mm) | (cm) | (cm) | ||
| SD/MS2-1-2 | 1/2 | 6.35 | SD/MS2-13 | 13 | 8 | ||
| SD/MS2-5-8 | 17.780 | 5/8 | 7.14 | SD/MS2-16 | 17.780 | 16 | 8 |
| SD/MS2-3-4 | 3/4 | 7.97 | SD/MS2-22 | 22 | 10 | ||
| SD/MS2-7-8 | 7/8 | 8.70 | SD/MS2-27 | 27 | 12 | ||
| SD/MS3-1-2 | 1/2 | 6.35 | SD/MS3-13 | 13 | 8 | ||
| SD/MS3-5-8 | 5/8 | 7.14 | SD/MS3-16 | 16 | |||
| SD/MS3-3-4 | 23.825 | 3/4 | 7.94 | SD/MS3-22 | 23.825 | 22 | 10 |
| SD/MS3-7-8 | 7/8 | 8.70 | SD/MS3-27 | 27 | 12 | ||
| SD/MS3-1 | 1 | 9.53 | SD/MS3-32 | 32 | 14 | ||
| SD/MS3-1-1/4 | 1-1/4 | 12.70 | SD/MS3-40 | 40 | 16 | ||
| SD/MS4-1-2 | 1/2 | 6.35 | SD/MS3-13 | 13 | 8 | ||
| SD/MS4-5-8 | 5/8 | 7.14 | SD/MS3-16 | 16 | |||
| SD/MS4-3-4 | 3/4 | 7.94 | SD/MS3-22 | 22 | 10 | ||
| SD/MS4-7-8 | 31.267 | 7/8 | 8.70 | SD/MS3-27 | 31.267 | 27 | 12 |
| SD/MS4-1 | 1 | 9.53 | SD/MS3-32 | 32 | 14 | ||
| SD/MS4-1-1/4 | 1-1/4 | 12.70 | SD/MS3-40 | 40 | 16 | ||
| SD/MS4W-1-1/2 | 1-1/2 | 15.88 | SD/MS3-50 | 50 | 18 | ||
| SD/MS5-1-2 | 1/2 | 6.35 | SD/MS3-16 | 16 | 8 | ||
| SD/MS5-5-8 | 5/8 | 7.14 | SD/MS3-22 | 22 | 10 | ||
| SD/MS5-3-4 | 3/4 | 7.94 | SD/MS3-27 | 27 | 12 | ||
| SD/MS5-7-8 | 44.399 | 7/8 | 8.70 | SD/MS3-32 | 44.399 | 32 | 14 |
| SD/MS5-1 | 1 | 9.53 | SD/MS3-40 | 40 | 16 | ||
| SD/MS5-1-1/4 | 1-1/4 | 12.70 | SD/MS3-50 | 50 | 18 | ||
| SD/MS5-1-1/2 | 1-1/2 | 15.88 | SD/MS3-60 | 60 | 20 | ||
| SD/MS5-2 | 2 | 19.05 | |||||
+86-13791381619
